Software, Firmware, Updates Please enter the name or product code of your device. Search for:

the wireless adapter on the computer being used to configure the AirStation. The computer used to configure the AirStation should be set to obtain an IP address automati-cally using a DHCP server. The WHR-G54S has a default LAN IP address of and Subnet Mask of Getting Ready Buffalo recommends using a wired network connection, where your computer is the default IP address of the AirStation from to, and DHCP The AirStation may be used as either a full wireless router or a simple access point. The switch has three positions: On (Router Mode) - The default LAN-side IP address is and DHCP and NAT are enabled. Off (AP Mode) - The default LAN-side IP address of the AirStation is, and Here you can find the default IP address and the username and password for the user interface of the Buffalo WZR-300HP N300 Gigabit WLAN router. This site also contains information about the preconfigured Wi-Fi settings of the device. Now steps in Buffalo, this has run solidly for 6 months without a reboot needed. Update: Now into 9 months of ownership I wanted to add a USB drive for media storage. One issue the Buffalo AirStation has is it cannot mount NTFS partitions, the standard for Windows since the days of XP. If the red DIAG light on the AirStation is lit or flashing after several minutes of being powered on, please consult Buffalo Technical Support. Page 5 Configuring the AirStation using an Ethernet Connection Step Configure your TCP/IP Settings Setup using OS X Setup in OS 9 or later Navigate to the Dock and Click on System Preferences. - Click Re: Buffalo AirStation WHR-HP-G54 This is for the WHR-G54S, but it will probabley be the same for your router. You need to go into the advanced settings of the router.


BUFFALO AirStationPro WAPM-1166D の設定 - … WAPM-1166D のIPアドレスはDHCPサーバーがある場合は、DHCPで取得されたアドレスを利用しますがこれを固定IPアドレスに変えます。 管理画面のトップページの上部の[詳細設定]ボタンをクリックします。 [LAN側IPアドレス設定]画面が表示されます。 BUFFALO WZR-HP-G450H友好固件用户手册 - 豆 …

* Never unplug the AC adapter while the Buffalo LED is blinking continuously. ** Turn off AirStation, wait for a few seconds, then turn it back on. *** Because the network addresses of both the Internet port (WAN port) and the LAN port are the same, it is not possible to establish communication. Change the LAN-side IP address of the AirStation.

Downloads Software, firmware and updates Here you will find the latest updates for your product. In addition to current software and firmware, you will also find operating instructions and utilities. show all Downloads Declaration of Conformity here you will find our EU Declaration of Conformity documents. DoC documents Technical Documentation – ErP Here you will … Accessing the user interface is necessary when you want to change the router configuration. For the Buffalo WHR-HP-G54, you have to do the following steps for access: Turn on router; Establish a connection between the device and the router via network cable or Wi-Fi* Open web browser; Enter IP address in the address bar and confirm with ‘Enter’ key Find Your Buffalo Router IP Address. Enter Your Buffalo Router IP Address Into an Internet Browser's Address Bar. Submit Your Buffalo Router Username and Password When Prompted By Your Router. For more information on how to login to your Buffalo router please see our Free Guides. Still can't login to your Buffalo router even when using the username and password for your router? DHCP IP Address Pool for up to 64 Address(es) PPTP Server Function Disable Authorization Type MS-CHAPv2 (40/128-bit Encryption) Server IP Address Auto Client IP Address Auto DNS Server IP Address LAN IP address of the AirStation WINS Server IP Address None PPTP User List None LAN Side IP Address Router Mode: (255.255 Networking > Apartments > Buffalo AirStation Setup Buffalo AirStation WHR-G125. After unpacking your Buffalo wireless router, connect the ethernet cable from your jack to the rightmost ethernet port on the back of the router. This is the blue WAN port labeled "Internet". Buffalo recommends using a wired connection for initial configuration, meaning your computer is physically connected to the AirStation with an Ethernet cable plugged into the LAN port of the WLA2-G54C and to a network computer. (The computer used to configure the AirStation should be set to obtain an IP address automatically using a DHCP server.) . Page 4: Configure Wireless Settings With Aoss Step 3: Configure Wireless Settings (with AOSS) AOSS (AirStation One-Touch Secure System) is a simple system for configuring your wireless network securely.